液壓萬能試驗機主要事項
發布時間：2018-11-23 來源：濟南恒思盛大儀器有限公司 瀏覽：
試驗機在使用操作過程中都有一些注意事項，這樣能更好的維護保養好試驗機，使其使用壽命更長，下面介紹一下液壓萬能試驗機的使用時注意的幾點。
Test machine has some matters needing attention in operation process, so better able tomaintain the testing machine, the service life is longer, here are a few pay attention to the use of hydraulic universal testing machine.
首先操作過程中，開關機的順序，由于試驗機受控于微機的控制軟件，應保證在試驗機打開時，軟件沒有關閉。
First, in the process of operation, the switch machine order, because the control softwaretesting machine controlled by microcomputer, shall ensure that opened in the testing machine, the software is not closed.
1.開機：打開微機（電腦）電源打開控制軟件打開試驗機電源。
1 boot: open the computer (computer) on the power control software to open the power of the testing machine.
2.關機：關閉試驗機電源關閉控制軟件關閉微機（電腦）電源。
2 off: close the test machine power down control software PC (computer) power off.
還有幾點注意：1.試驗機的關鍵部位（如：鉗口、變速箱等）應經常加注潤滑油脂。
There are a few points to note: the key parts of the 1 test machine (such as: jaw, gear box)should be regularly lubricating oil.
2.電腦應放在干燥通風的室內。
2 computer should be placed in dry and ventilated room.
3.若長時間不使用，每個月應通電運轉一次。
3 if you do not use a long time, every month should be energized operation a.
再就是使用的軟件環境：須安裝Office2000（Word2000、Access2000）
Then use the software environment: to install Office2000 (Word2000, Access2000)
還有關于檢修方面需注意的幾點：液壓萬能試驗機主要?jiǎng)恿κ且簤簷C(jī)，在所以試驗機或者是工廠中使用總要是正確使用和保養，而檢修是預防設備出問題重要方案，
There are a few points to note: maintenance of hydraulic universal testing machine is the main force in hydraulic machine, so testing machine or is the most general if the proper use and maintenance of the use of the factory, and maintenance is important for prevention ofequipment problems,
1.檢修步驟：首先液壓油換掉，然后各個氣管通絡全都打開，鼓風機的氣壓進行把氣管插到鼓風機上，對液壓萬能試驗機內腔清理，使里面廢油和臟東西清理干凈。
1 maintenance steps: firstly, the hydraulic oil to change, and then all tracheal Tongluo allopen, the pressure of the air blower is inserted into the blower, cleaning of the inner cavity of hydraulic universal testing machine, so that the inside of waste oil and dirty things clean.
http://m.hkbzzp.com/
